Commercial Z955M MOD

Double tap to zoom



  • Deck can be converted from a wide-open side discharge mode to a fully chambered mulching mode with a single move of a lever. NOTE: MOD decks are a balance between a side discharge deck and a side discharge deck with a mulching kit.
  • Deck is stamped from 7-gauge, 0.179-in. (4.6-mm) steel to minimize the number of welds and provide a smooth underside, with fewer sharp corners, for reduced material buildup.
  • Significantly fewer welds on the deck shell to wear or break- it is stamped from a single sheet of steel rather than multiple fabrications. Anti-skid step on the deck provides for easy machine mounting.
  • MOD decks are superior to aftermarket chute blockers due to the movable baffles.
  • Higher blade tip speed than many competitors - 18,500 fpm (5,639 m/min) for more blade cuts per inch mowed.
  • Rounded corners of the stamped deck help distribute impact stress to reduce the potential of damage when the mower contacts trees, rocks, curbs, and other fixed obstacles.
  • Deep-deck design of 5.5 in. (14 cm) delivers excellent airflow so material can be processed quickly and efficiently.
  • Wider and higher discharge opening provides even clipping dispersal for an excellent finished appearance in all conditions.
  • Three 1-in. (2.5 cm) cold-forged spindles are heat-treated for strength without bulk and are supported by ball bearings, providing reliability and performance; spindle housings are ribbed cast aluminum providing both excellent strength and heat dissipation.
  • The front edge is raised above the blade plane to allow even cutting of tall grass and reinforced with a square bar for durability. The front baffle has been redesigned to better manage airflow and control clippings.
  • Dual-captured anti-scalp wheels provide deck flotation over even the toughest terrain.
  • Three greasable spindle zerks accessible from the top.
  • Blade overlap is 1.6 in. (40 mm), nearly 0.79 in. (20 mm) greater than previous decks, to reduce striping between blades.
  • Quick-change, cutting-height adjustment.


Model no. ECV860J EFI
Horsepower (gross) At 3,600 rpm, 29 hp 21.6 kW
Displacement 50.3 cu in. 824 cc
Cylinders Two
Crankcase capacity With filter, 2.7 U.S. qt 2.6 L
Oil filter Full flow, replaceable
Lubrication Full pressure
Cooling Air
Air cleaner Pre-cleaner Yes Heavy-duty canister type with safety element
Fuel type Gasoline
Fuel consumption Under normal conditions, load, operation, and dependent on loads and operating conditions 1.0-1.8 U.S. gal./hr 3.8-6.8 L/hr
Fuel tank capacity 11.5 U.S. gal. 43.5 L
Fuel tank switch/shut-off valve Yes
Charge system 20 amp
Battery voltage 12 V
Cold cranking amp 300 amp
Hour meter Standard, digital
Operator presence starting system Brake-N-Go (hand)
Wheel motors Tuff Torq heavy-duty integrated piston wheel motor
Travel speed Forward 0-10 mph 0-16.1 km/hReverse 0-4.5 mph 0-7.2 km/h
Speed and direction control Twin levers
Hydraulic capacity 5.9 U.S. qt 5.6 L
Hydraulic oil cooler  
Filter Internal, replaceable
Hydraulic pumps  
Drive tires 24x12-12
Rear tires  
Load rating 4 PR
Dynamic braking Twin levers
Park brake Internal wet disk integrated in the transmission
Park brake actuation Hand brake
Type Electro-magnetic, 225 lb-ft 305 Nm
Drive V-belt
Available widths 60, 72 in. 152, 183 cm
Deck construction 7Iron PRO, one-piece stamped steel with reinforcements
Deck thickness 7 gauge 0.18 in. 4.6 mm
Discharge Side, MOD
Height-of-cut range Increments 0.25 in. 0.64 cm 1-5.5 in. 2.54-14 cm
Cutting width 60, 72 in. 152, 183 cm
Length Varies by deck size
Thickness 0.25 in. 0.64 cm
Tip speed Approximately 18,000 fpm 5,486 m/min
Number Three
Caster wheel type Flat free
Caster wheel size 13x6.5-6
Front anti-scalp rollers RH, center, LH
Rear anti-scalp rollers Optional
Length 84 in. 213.4 cm
Width With chute down, 74, 86 in. 188, 218.4 cm
Height With ROPS up, 73 in. 185.4 cm With ROPS down, 47 in. 119.4 cm
Weight 1,275 to1,365 lb 578 to 619 kg

SAVE TIME and schedule your service visit today